Candle candles silicone mold silicone mold characteristics: ① mold silicone rubber to have good performance. ② silica gel better flowability, low viscosity easy to operate. ③ silicone rubber shrinkage as small as possible. ④ silicone rubber tension better. ⑤ made out of silicone mold can not be deformed. ⑥ hardness silicone rubber to fit the product. ⑦ temperature, turn mode more often, life is longer, acid and alkali resistance, aging resistance. Production method of a silicone mold candles, plastic bowl filled with a 500g plastic, reinforcing agent at room temperature for 1.5%, stir evenly spare. 2, the mother mold release agent treated blanks with lubrication. 3, lubrication good mother surrounded by green wood surround, wood releasing treatment is also applied in the middle of the gap to 2-4cm is appropriate. 4, along with a good glue slowly pouring a fixed perfusion point, not when the shock to exclude the air inside. 5,60 minutes after four weeks and then glue cured completely surrounded by wood, leaving 4cm gap, dismantle wood strips. 6, after the injection of gypsum powder 1000g watered wooden box, filled up (use plastic piece of wood box divided into two parts in order to facilitate the form removal). 7.20 minutes after the removal of wood, mold that made complete. Note: 1, plus the amount of curing agent should be depending on temperature, high temperature decreased. Excess curing agent, the mold will be hard and brittle; curing agent is too small, the operating time is extended. 2, in order to prevent changes in the physical properties of silicone mold, it is recommended not to add silicone oil. 3, in order to mold you can achieve the best results, please die storage at least 24 hours after use. 4 die can also be made of resin. Operation candles silicone mold: 1, silicone and silicone mold curing agent Stir liquid flowing appearance, A component is silica, component B is the curing agent. Example: Take 100 grams of silica gel, 2 g of curing agent (Note: silicone and hardener must stir, stir if not, there will be a mold has been cured, a no curing, silicone will be uneven drying and curing conditions on will affect the life of the silicone mold and turning model number, even resulting in mold scrapped condition 2, vacuum row bubble treatment: silica gel and curing agent Stir evacuated rows of bubbles links, vacuuming time not too long under normal circumstances, not more than ten minutes, vacuum too long, once cured silicone, resulting in a cross-linking reflect that turned into a piece of silicone can not be painted or perfusion, thus wasting silicone, can only silicone into the trash, do re-take the silicone 3, brushing or procedure: The row over the bubbles evacuated silica gel, brushing or perfusion way down in the product above (Note: Before you want to copy down the silica product or model is absolutely necessary to release agent or release agent). then put silicone products above brushing, brushing must be uniform, 30 minutes after pasting a layer of gauze fiber silicone sheeting to increase the intensity and tension. Then then brushing a layer of silica gel, and then paste a layer of gauze fiber sheeting, after so twice on it. Only by doing so, open up the silicone mold life and turning model to improve the lot number of a relative, you can save costs and improve efficiency 4, the outer mold making: General methods and materials used is to mold around with a plastic sheet or boarded up, a cabinet filled with plaster to mold it, another way of using resin painted, painted brush on a layer of resin paste layer of fiberglass cloth, then brushing then paste, repeated two or three to complete the outer mold mold 5, the operation method of filling the mold or perfusion mode: mold filling or perfusion mode, is used relatively smooth or simple product, there is no parting line saving time and labor, that is, the product or model you want to copy, enclosed with a plastic sheet or a glass plate, the smoked vacuum silicone directly into the products above, to be molded silicone dry After removal products, mold on the shape (Note: perfusion mode generally used hardness is relatively soft silicone mold to do, so stripping easier, will not damage the silicone mold inside the product) to your order to find a long-term trust. material suppliers! Hongye silicone is your ideal choice!